Kanthal® LT

Resistance heating wire and resistance wireDatasheet

Datasheet updated 2021-02-04 13:31 (supersedes all previous editions)

Disclaimer: Recommendations are for guidance only, and the suitability of a material for a specific application can be confirmed only when we know the actual service conditions. Continuous development may necessitate changes in technical data without notice. This datasheet is only valid for materials under the trademark Kanthal^®.

Kanthal^® LT is a ferritic iron-chromium-aluminium alloy (FeCrAl alloy) for use at temperatures up to which 1100°C (2010°F). The alloy is characterized by moderate resistivity and good oxidation resistance.

Kanthal^® LT is typically used in home appliances.

Chemical composition

	C %	Si %	Mn %	Cr %	Al %	Fe %
Nominal composition					3.8	Bal.
Min	-	-	-	17.0	-
Max	0.08	0.7	0.5	21.0	-

Mechanical properties

Wire size	Yield strength	Tensile strength	Elongation	Hardness
Ø	R_p0.2	R_m	A
mm (in)	MPa (ksi)	MPa (ksi)	%	Hv
1.0 (0.04)	550 (80)	750 (109)	16	230

Mechanical properties at elevated temperature
Temperature °C (°F)	900 (1652)
MPa (ksi)	34 (4.9)

Ultimate tensile strength - deformation rate 6.2 x 10^-2/min

Creep strength - 1% elongation in 1000 h
Temperature °C (°F)	800 (1472)	1000 (1832)
MPa (psi)	1.2 (170)	0,5 (73)

Physical properties

Density g/cm³(lb/in³)	7.30 (0.264)
Electrical resistivity at 20°C Ω mm²/m (Ω circ. mil/ft)	1.23 (740)
Poisson's ratio	0.30

Young's modulus
Temperature °C	20	100	200	400	600	800	1000
Temperature °F	68	212	392	752	1112	1472	1832
GPa	220	210	205	190	170	150	130
Msi	32	30	30	28	25	22	19

Temperature factor of resistivity
Temperature °C	100	200	300	400	500	600	700	800	900	1000	1100
Temperature °F	212	392	572	752	932	1112	1292	1472	1652	1832	2012
Ct	1.00	1.02	1.03	1.04	1.05	1.08	1.09	1.10	1.11	1.11	1.12

Coefficient of thermal expansion
Temperature °C (°F)	Thermal Expansion x 10^-6/K (10^-6 /°F)
20 - 250 (68-482)	11 (6.1)
20 - 500 (68-932)	12 (6.7)
20 - 750 (68-1382)	14 (7.8)
20 - 1000 (68-1832)	15 (8.3)

Thermal conductivity
Temperature °C (°F)	20 (68)
W m^-1 K^-1(Btu h^-1ft^-1°F^-1)	16 (9.3)

Specific heat capacity
Temperature °C (°F)	20 (68)
kJ kg^-1 K^-1 (Btu lb^-1°F^-1)	0.46 (0.11)

Melting point °C (°F)	1500 (2732)
Max continuous operating temperature in air °C (°F)	1100 (2012)
Magnetic properties	The material is magnetic up to approximately 600°C (1112°F)(Curie point).
Emissivity - fully oxidized material	0.70

Kanthal® LT

Chemical composition

Mechanical properties

Physical properties

Send PDF via email

About Kanthal

About Alleima